Reply to thread

Message: <blockquote data-quote="AuroraGirl" data-source="post: 30006" data-attributes="member: 9417"><p> <table style='width: 100%'><tr><td>[H4]Tools Required[/H4]<br /> <p style="text-align: left"><table style='width: 100%'><tr><td>    • </td><td>Urethane Adhesive Kit GM P/N 12346392 or Equivalent</td></tr></table><table style='width: 100%'><tr><td>    • </td><td>Isopropyl Alcohol or Equivalent</td></tr></table><table style='width: 100%'><tr><td>    • </td><td>Cartridge-type Caulking Gun</td></tr></table><table style='width: 100%'><tr><td>    • </td><td>Plastic Paddle</td></tr></table></p> <a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58307#ss1-716780" target="_blank">[H3]Removal Procedure[/H3]</a><br /> <ol> <li data-xf-list-type="ol">Remove both right and left sides of the reveal molding. Refer to <a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58323" target="_blank">Windshield Side Reveal Molding Replacement</a> .</li> <li data-xf-list-type="ol"><img src="https://gm.saturn.team/images/301108.gif" alt="Object Number: 301108 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /><br /> <strong>Caution: </strong>When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.<br /> <strong>Important: </strong>The windshield reveal molding fills the cavities between the body and windshield. If the reveal molding is stretched or damaged it and cannot be reused it must be replaced.</li> <li data-xf-list-type="ol">Remove the upper windshield reveal molding.</li> <li data-xf-list-type="ol"><p style="text-align: left"><table style='width: 100%'><tr><td>2.1. </td><td>Use a flat-bladed tool in order to carefully pry the end of the upper reveal molding out about 76 mm (3 in).</td></tr></table><table style='width: 100%'><tr><td>2.2. </td><td>Grasp the corner of the windshield reveal molding by hand or use a suitable tool to slowly pull the reveal molding away from the windshield.</td></tr></table><table style='width: 100%'><tr><td>2.3. </td><td>If the windshield reveal molding will not release, use a utility knife to aid in the releasing of the molding.</td></tr></table></p> </li> </ol> <a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58307#ss2-716780" target="_blank">[H3]Installation Procedure[/H3]</a><br /> <ol> <li data-xf-list-type="ol">Clean the top edge of the windshield surface with a 50/50 mixture of isopropyl alcohol and water by volume on a dampened lint - free cloth.</li> <li data-xf-list-type="ol">The new reveal molding should be fitted to the windshield prior to installation.</li> <li data-xf-list-type="ol"><strong>Caution: </strong>When replacing stationary windows, use Urethane Adhesive Kit GM P/N 12346392 (Canadian P/N 10952983), or a urethane adhesive system meeting GM Specification GM3651G, to maintain original installation integrity. Failure to use the urethane adhesive kit will result in poor retention of the window which may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.</li> <li data-xf-list-type="ol">Verify all primers and urethane adhesive are within expiration dates.</li> <li data-xf-list-type="ol"><img src="https://gm.saturn.team/images/739026.gif" alt="Object Number: 739026 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /><br /> <strong>Important: </strong>Use care when applying the prep (clear #1) to the windshield. This primer dries almost instantly, and may stain the viewing area of the windshield if not applied evenly.</li> <li data-xf-list-type="ol">Use a new dauber in order to apply glass prep (clear #1) to the channel area approximately 13 mm (1/2 in) to the upper edge of the windshield.</li> <li data-xf-list-type="ol">Wipe the glass primed area immediately with a clean lint-free cloth.</li> <li data-xf-list-type="ol">Shake the glass primer (black #2) for at least one minute.</li> <li data-xf-list-type="ol">Using a new dauber in order to apply glass primer (black #2) to the top edge of the windshield.<br /> <img src="https://gm.saturn.team/images/245294.gif" alt="Object Number: 245294 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Apply a small bead of urethane adhesive (2) between the windshield (1) and the pinchweld.</li> <li data-xf-list-type="ol"><img src="https://gm.saturn.team/images/301108.gif" alt="Object Number: 301108 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Install the upper reveal molding.</li> <li data-xf-list-type="ol"><p style="text-align: left"><table style='width: 100%'><tr><td>8.1. </td><td>Start from the center and hand-press the reveal molding into place over the edge of the windshield.</td></tr></table><table style='width: 100%'><tr><td>8.2. </td><td>Install both right and left sides of the reveal molding. Refer to <a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58323" target="_blank">Windshield Side Reveal Molding Replacement</a> .</td></tr></table><table style='width: 100%'><tr><td>8.3. </td><td>Run warm water over the reveal molding in order to speed the setup time of the urethane adhesive.</td></tr></table></p> Tape should be applied in order to retain the reveal molding to the windshield, this will maintain a flush fit with the body.<br /> The tape is to be removed after 6 hou</li> </ol> </td></tr></table><p></p><p>because it says to remove the side moldings First here is the side moldings : </p><table style='width: 100%'><tr><td><a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58323#ss1-741249" target="_blank">[H3]Removal Procedure[/H3]</a><br /> <br /> <ol> <li data-xf-list-type="ol"><img src="https://gm.saturn.team/images/441415.gif" alt="Object Number: 441415 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Pull back the front door sealing weatherstrip (1) to expose the windshield reveal molding screws.</li> <li data-xf-list-type="ol"><img src="https://gm.saturn.team/images/301107.gif" alt="Object Number: 301107 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Remove the screws from the windshield reveal molding.</li> <li data-xf-list-type="ol">Remove the windshield reveal molding from the windshield pillar.</li> </ol> <a href="https://gm.saturn.team/Chevrolet/Chevy_C_Silverado___2WD/2004/30/30/2954/58323#ss2-741249" target="_blank">[H3]Installation Procedure[/H3]</a><br /> <br /> <ol> <li data-xf-list-type="ol">Install the windshield reveal molding to the windshield pillar.</li> <li data-xf-list-type="ol"><strong>Notice: </strong>Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.<br /> <img src="https://gm.saturn.team/images/301107.gif" alt="Object Number: 301107 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Install the screws to the windshield reveal molding.</li> <li data-xf-list-type="ol"><strong>Tighten</strong><br /> Tighten the screws to the windshield reveal molding to 2 N·m (18 lb in).<br /> <img src="https://gm.saturn.team/images/441415.gif" alt="Object Number: 441415 Size: SH" class="fr-fic fr-dii fr-draggable " style="" /></li> <li data-xf-list-type="ol">Install the front door sealing weatherstrip (1) to the pinch-weld.</li> <li data-xf-list-type="ol">Close the door.</li> </ol> </td></tr></table></blockquote><p></p>